Gentoo Wiki ArchivesGentoo Wiki

HP_dv6565en/dmesg

File: gentoo dmesg
 
gentoo bin # dmesg
Initializing cgroup subsys cpuset
Linux version 2.6.24-gentoo-r5 (root@miranda) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #1 SMP Thu Apr 24 01:42:27 UTC 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
 BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007ff60000 (usable)
 BIOS-e820: 000000007ff60000 - 000000007ff6e000 (ACPI data)
 BIOS-e820: 000000007ff6e000 - 000000007ff6f000 (ACPI NVS)
 BIOS-e820: 000000007ff6f000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f8640
NX (Execute Disable) protection: active
Entering add_active_range(0, 0, 524128) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   524128
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   524128
On node 0 totalpages: 524128
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 2302 pages used for memmap
  HighMem zone: 292450 pages, LIFO batch:31
  Movable zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000F8590, 0024 (r2 PTLTD )
ACPI: XSDT 7FF64304, 006C (r1 HPQOEM SLIC-MPC  6040000  LTP        0)
ACPI: FACP 7FF6D8E8, 00F4 (r3 NVIDIA MCP65-E   6040000 PTL_    F4240)
ACPI: DSDT 7FF64370, 9504 (r1 NVIDIA    MCP65  6040000 MSFT  3000000)
ACPI: FACS 7FF6EFC0, 0040
ACPI: SRAT 7FF6D9DC, 00A0 (r1 AMD    HAMMER    6040000 AMD         1)
ACPI: WDAT 7FF6DA7C, 0104 (r1 PTLTD  WDATTBL   6040000  LTP        1)
ACPI: SSDT 7FF6DB80, 0206 (r1 PTLTD  POWERNOW  6040000  LTP        1)
ACPI: MCFG 7FF6DD86, 003C (r1 HP       MCFG    6040000  LTP        0)
ACPI: HPET 7FF6DDC2, 0038 (r1 PTLTD  HPETTBL   6040000  LTP        1)
ACPI: APIC 7FF6DDFA, 0068 (r1 HP     	 APIC    6040000  LTP        0)
ACPI: BOOT 7FF6DE62, 0028 (r1     HP $SBFTBL$  6040000  LTP        1)
ACPI: SLIC 7FF6DE8A, 0176 (r1 HPQOEM SLIC-MPC  6040000  LTP        1)
ACPI: DMI detected: Hewlett-Packard
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:8 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d0000
swsusp: Registered nosave memory region: 00000000000d0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 520034
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sdb3 
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0575000 soft=c0535000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1908.695 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2046952k/2096512k available (2741k kernel code, 48304k reserved, 1197k data, 328k init, 1179008k highmem)
virtual kernel memory layout:
    fixmap  : 0xffc74000 - 0xfffff000   (3628 kB)
    pkmap   : 0xffa00000 - 0xffc00000   (2048 kB)
    vmalloc : 0xf8800000 - 0xff9fe000   ( 113 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc04df000 - 0xc0531000   ( 328 kB)
      .data : 0xc03ad50c - 0xc04d8bc4   (1197 kB)
      .text : 0xc0100000 - 0xc03ad50c   (2741 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet clockevent registered
Calibrating delay using timer specific routine.. 3820.54 BogoMIPS (lpj=19102719)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(2) -> Core 0
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-58 stepping 01
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c0576000 soft=c0536000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3817.34 BogoMIPS (lpj=19086737)
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1(2) -> Core 1
AMD C1E detected late. 	Force timer broadcast.
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-58 stepping 01
Total of 2 processors activated (7637.89 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 2 CPUs
CPU0 attaching sched-domain:
 domain 0: span 00000000,00000003
  groups: 00000000,00000001 00000000,00000002
CPU1 attaching sched-domain:
 domain 0: span 00000000,00000003
  groups: 00000000,00000002 00000000,00000001
net_namespace: 64 bytes
Booting paravirtualized kernel on bare hardware
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  :  5476.400 MB/sec
xor: using function: pIII_sse (5476.400 MB/sec)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:08.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR3._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5) *15
ACPI: PCI Interrupt Link [LNK2] (IRQs 7) *10
ACPI: PCI Interrupt Link [LNK3] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LK1E] (IRQs 16) *11
ACPI: PCI Interrupt Link [LK2E] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [LK3E] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [LK4E] (IRQs 19) *15
ACPI: PCI Interrupt Link [LSMB] (IRQs *10)
ACPI: PCI Interrupt Link [LUS0] (IRQs 18) *11
ACPI: PCI Interrupt Link [LUS2] (IRQs 17) *7
ACPI: PCI Interrupt Link [LMAC] (IRQs 20) *10
ACPI: PCI Interrupt Link [LAZA] (IRQs 21) *11
ACPI: PCI Interrupt Link [LPID] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 23) *5
ACPI: PCI Interrupt Link [LPMU] (IRQs 11) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
ACPI Error (dsopcode-0548): Field [I9MN] at 544 exceeds Buffer [IORT] size 464 (bits) [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.LPC0.PMIO._CRS] (Node f7c37914), AE_AML_BUFFER_LIMIT
ACPI Error (uteval-0233): Method execution failed [\_SB_.PCI0.LPC0.PMIO._CRS] (Node f7c37914), AE_AML_BUFFER_LIMIT
pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0c02
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
ACPI: RTC can wake from S4
Time: hpet clocksource has been installed.
Clockevents: could not switch to one-shot mode: lapic is not functional.
Could not switch to high resolution mode on CPU 0
Clockevents: could not switch to one-shot mode: lapic is not functional.
Could not switch to high resolution mode on CPU 1
system 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:03: ioport range 0x360-0x361 has been reserved
system 00:03: ioport range 0x4d0-0x4d1 has been reserved
system 00:0a: iomem range 0xffc00000-0xffffffff could not be reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0a: iomem range 0xfed00000-0xfed00fff has been reserved
system 00:0a: iomem range 0xfec80000-0xfec80fff has been reserved
system 00:0a: iomem range 0xfef00000-0xfef00fff has been reserved
PCI: Bridge: 0000:00:08.0
  IO window: disabled.
  MEM window: f2100000-f21fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0b.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
  IO window: disabled.
  MEM window: f2000000-f20fffff
  PREFETCH window: disabled.
PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:05:00.0
PCI: Bridge: 0000:00:0d.0
  IO window: 4000-4fff
  MEM window: cc000000-ceffffff
  PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:0e.0
  IO window: 5000-5fff
  MEM window: f0000000-f1ffffff
  PREFETCH window: f2600000-f27fffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 25860k freed
Simple Boot Flag at 0x36 set to 0x1
Machine check exception polling timer started.
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1211719932.960:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.3 (2007/10/31) Phillip Lougher
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Boot video device is 0000:05:00.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
hpet_resources: 0xfed00000 is busy
Generic RTC Driver v1.07
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP65: IDE controller (0x10de:0x0448 rev 0xa1) at  PCI slot 0000:00:09.0
NFORCE-MCP65: not 100% native mode: will probe irqs later
NFORCE-MCP65: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP65: 0000:00:09.0 (rev a1) UDMA133 controller
    ide0: BM-DMA at 0x30c0-0x30c7, BIOS settings: hda:DMA, hdb:pio
NFORCE-MCP65: IDE port disabled
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-T20L, ATAPI CD/DVD-ROM drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: MWDMA2 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Loading iSCSI transport class v2.0-724.
iscsi: registered transport (tcp)
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1    752 MB/s
raid6: int32x2    756 MB/s
raid6: int32x4    686 MB/s
raid6: int32x8    501 MB/s
raid6: mmxx1     1549 MB/s
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input2
raid6: mmxx2     2685 MB/s
raid6: sse1x1    1520 MB/s
raid6: sse1x2    2587 MB/s
raid6: sse2x1    2574 MB/s
raid6: sse2x2    3512 MB/s
raid6: using algorithm sse2x2 (3512 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
cpuidle: using governor ladder
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 328k freed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 16, io mem 0xf2488000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-4: new high speed USB device using ehci_hcd and address 5
usb 1-4: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
USB Universal Host Controller Interface driver v3.0
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
sl811: driver sl811-hcd, 19 May 2005
PCI: Enabling device 0000:07:05.0 (0100 -> 0102)
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5
ACPI: PCI Interrupt 0000:07:05.0[A] -> Link [LNK1] -> GSI 5 (level, low) -> IRQ 5
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5]  MMIO=[f2100000-f21007ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
ahci 0000:00:0a.0: version 3.0
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LTID] -> GSI 23 (level, low) -> IRQ 17
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00241b00d2f03500]
ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
ahci 0000:00:0a.0: flags: 64bit ncq sntf pm led clo pmp pio 
PCI: Setting latency timer of device 0000:00:0a.0 to 64
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
ata1: SATA max UDMA/133 abar m8192@0xf2484000 port 0xf2484100 irq 17
ata2: SATA max UDMA/133 abar m8192@0xf2484000 port 0xf2484180 irq 17
ata3: SATA max UDMA/133 abar m8192@0xf2484000 port 0xf2484200 irq 17
ata4: SATA max UDMA/133 abar m8192@0xf2484000 port 0xf2484280 irq 17
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: ST9160821AS, 3.BHD, max UDMA/100
ata1.00: 312581808 sectors, multi 16: LBA48 
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 1:0:0:0: Direct-Access     ATA      ST9160821AS      3.BH PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg0 type 0
NCR53c406a: no available ports found
scsi: <fdomain> Detection failed (no card)
GDT-HA: Storage RAID Controller Driver. Version: 3.05
GDT-HA: Found 0 PCI Storage RAID Controllers
usb-storage: device scan complete
scsi 0:0:0:0: Direct-Access     WD       2500BEV External 1.04 PQ: 0 ANSI: 4
sd 0:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sdb] Write Protect is off
sd 0:0:0:0: [sdb] Mode Sense: 21 00 00 00
sd 0:0:0:0: [sdb] Assuming drive cache: write through
sd 0:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sdb] Write Protect is off
sd 0:0:0:0: [sdb] Mode Sense: 21 00 00 00
sd 0:0:0:0: [sdb] Assuming drive cache: write through
 sdb:<6>qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>seagate: ST0x/TMC-8xx not detected.
Failed initialization of WD-7000 SCSI card!
NCR53c406a: no available ports found
sym53c416.c: Version 1.0.0-ac
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SPI Host driver 3.04.06
Fusion MPT FC Host driver 3.04.06
Fusion MPT SAS Host driver 3.04.06
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.14)
Adaptec aacraid driver 1.1-5[2449]-ms
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007
QLogic Fibre Channel HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.2.2
Copyright(c) 2004-2007 Emulex.  All rights reserved.
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
 sdb1 sdb2 < sdb5 sdb6 sdb7 > sdb3
sd 0:0:0:0: [sdb] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg1 type 0
md: raid10 personality registered for level 10
JFS: nTxBlock = 8192, nTxLock = 65536
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: sdb3: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 385417
ext3_orphan_cleanup: deleting unreferenced inode 385408
ext3_orphan_cleanup: deleting unreferenced inode 385415
ext3_orphan_cleanup: deleting unreferenced inode 385414
ext3_orphan_cleanup: deleting unreferenced inode 385413
ext3_orphan_cleanup: deleting unreferenced inode 385412
ext3_orphan_cleanup: deleting unreferenced inode 385411
ext3_orphan_cleanup: deleting unreferenced inode 385410
ext3_orphan_cleanup: deleting unreferenced inode 385409
ext3_orphan_cleanup: deleting unreferenced inode 385220
ext3_orphan_cleanup: deleting unreferenced inode 385407
ext3_orphan_cleanup: deleting unreferenced inode 385406
ext3_orphan_cleanup: deleting unreferenced inode 385405
ext3_orphan_cleanup: deleting unreferenced inode 385404
ext3_orphan_cleanup: deleting unreferenced inode 385222
ext3_orphan_cleanup: deleting unreferenced inode 385221
ext3_orphan_cleanup: deleting unreferenced inode 383541
ext3_orphan_cleanup: deleting unreferenced inode 385219
ext3_orphan_cleanup: deleting unreferenced inode 385218
ext3_orphan_cleanup: deleting unreferenced inode 385217
ext3_orphan_cleanup: deleting unreferenced inode 385212
ext3_orphan_cleanup: deleting unreferenced inode 383550
EXT3-fs: sdb3: 22 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /devices/platform/pcspkr/input/input3
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LMAC] -> GSI 20 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:06.0 to 64
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
bcm43xx driver
forcedeth 0000:00:06.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1b:24:6a:b4:c2
forcedeth 0000:00:06.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3
ricoh-mmc: Ricoh MMC controller found at 0000:07:05.2 [1180:0843] (rev 12)
ricoh-mmc: Controller is now disabled.
sdhci: SDHCI controller found at 0000:07:05.1 [1180:0822] (rev 22)
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 7
ACPI: PCI Interrupt 0000:07:05.1[B] -> Link [LNK2] -> GSI 7 (level, low) -> IRQ 7
sdhci:slot0: Will use DMA mode even though HW doesn't fully claim to support it.
mmc0: SDHCI at 0xf2100800 irq 7 DMA
ACPI: PCI Interrupt Link [LK1E] enabled at IRQ 16
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LK1E] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:03:00.0 to 64
bcm43xx: Chip ID 0x4311, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0x13, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0xd, vendor 0x4243
bcm43xx: Unsupported 80211 core revision 13
bcm43xx: Core 2: ID 0x817, rev 0x4, vendor 0x4243
bcm43xx: Core 3: ID 0x820, rev 0x5, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 4, Type 2, Revision 9
bcm43xx: Invalid PHY Revision 9
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio initialized
bcm43xx: Radio initialized
thermal: Unknown symbol acpi_processor_set_thermal_limit
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:07.0[B] -> Link [LAZA] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:07.0 to 64
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /devices/virtual/input/input4
ohci_hcd: Unknown symbol ssb_device_disable
ohci_hcd: Unknown symbol ssb_admatch_base
ohci_hcd: Unknown symbol ssb_device_enable
ohci_hcd: Unknown symbol ssb_driver_unregister
ohci_hcd: Unknown symbol __ssb_driver_register
ohci_hcd: Unknown symbol ssb_admatch_size
ACPI: Power Button (FF) [PWRF]
ACPI: AC Adapter [ACAD] (on-line)
input: Lid Switch as /devices/virtual/input/input5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
ACPI: Lid Switch [LID]
input: Power Button (CM) as /devices/virtual/input/input6
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /devices/virtual/input/input7
ACPI: Sleep Button (CM) [SLPB]
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input8
ACPI: Video Device [UVGA] (multi-head: yes  rom: no  post: no)
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:25/LNXVIDEO:01/input/input9
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
ACPI Exception (thermal-0339): AE_BAD_DATA, No critical threshold [20070126]
EXT3 FS on sdb3, internal journal
Adding 2144636k swap on /dev/sdb7.  Priority:-1 extents:1 across:2144636k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present

Retrieved from "http://www.gentoo-wiki.info/HP_dv6565en/dmesg"

Last modified: Thu, 28 Aug 2008 16:09:00 +1000 Hits: 2,053

Created by NickStallman.net, Luxury Homes Australia
Real estate agents should list their apartments, townhouses and units in Australia.